Temporarily Out Of Stock
Don't get too bummed. This item is on the way and will be available for purchase as soon as it rolls into the warehouse.
Can't wait? Consider one of the other Mountain Bike Wheels we have in stock.View Similar Products
Pillar Carbon Trail Wheelset
Wheels are the most important component you can hang on a bike. The weight and stiffness of your wheels affects every aspect of the ride. Industry Nine is one of the most respected names in cycling, and wheels are all it makes. The Pillar Carbon 29 Trail Wheelset is Industry Nine’s top dog for all-mountain riding — no expense was spared in the design and manufacture of the Pillar line. The Pillar Carbon rim is light and stiff and is laced to Industry Nine’s best hub, the Torch. Don’t let its light weight fool you — the Carbon Trail 29 can take a beating. In other words, you’re looking at the best of the best in 29-inch mountain wheels.
These aren't just any run-of-the-mill epoxy and fiber-reinforced rings. Industry Nine enlisted help from the composite wizards at Reynolds Cycling. This means that these 28mm-wide outer, 24mm inner, tubeless rims feature Reynolds' MR5 technology. It focuses on five key elements — spoke face, nipple bed, tire channel, rim sidewall, and hook bead — in order to optimize resin chemistry and carbon layup for the structural loads of each component. The result is the Pillar Carbon rim with Twin Pillar hookless bead walls. The rims, found exclusively on Industry Nine’s Pillar line of wheels, are tubeless-ready and offer an excellent strength-to-weight ratio and ride quality characteristics.
The Carbon Trail 29 uses 32 spokes per wheel for durability. Instead of steel spokes, I9's wheels use 7075 aluminum. The spokes are straight pull, and they have a 25% greater cross section then comparable 14/15 double butted steel spokes. In other words, these spokes have a stronger tensile strength. Also, on traditional spokes, threads are rolled, not cut. This adds to strength, but creates a stress riser where the thread channel is narrower than the diameter of spoke itself.
Industry Nine, however, doesn't need to roll its threads. Instead, they're created during the machining process, but cut so that the thread channel is the same as the spoke's diameter. The threads themselves are actually larger than the spoke for a strong interface with the hub. That brings to light another defining feature of these wheels — there are no nipples. The spokes thread directly into hub and use a standard 15-gauge wrench and conventional truing methods in order to service. The Torch hubs that these spokes thread into are a fresh redesign of the groundbreaking Industry Nine hubs.
Industry Nine's new Torch hubs feature two sets of three pawls spaced three degrees apart. This preserves the 120 points of contact and lightning-quick three degrees engagement that distinguished Industry Nine, only now, the pawls have two teeth instead of three. Along with that, a changed cantilever angle and shallower tooth profile on the hardened drive ring reduce drag for a less-restricted freehub. Remarkably, it has the same holding power. And, that's not all that I9 did to improve the Torch.
Its engineers removed the large bearing between the freehub body and shell, opting for smaller bearings directly between the body and shell. The reduced bearing size means less seal surface area that, along with a new silicone lip design, significantly reduces mechanical drag. The freehub is also now easier to remove for cleaning/lubing, and like before, the springs and pawls are captured. So, you won't be scrambling on a floor looking for small parts.
- Item #NIN000J
- Rim Material
- carbon fiber
- Wheel Size
- 29 in
- Tire Type
- Rim Width
- [external] 28 mm, [internal] 24 mm
- Brake Compatibility
- 6-bolt disc
- Industry Nine Torch
- Front Axle
- 15mm QR
- Rear Axle
- 12x142 mm thru-axle
- 2.9 / 2.7mm butted + 2.9mm straight gauge
- Spoke Count
- 24 / 24
- Recommended Use
- Manufacturer Warranty
- 3 years
What do you think about this product?